BENNETT CUSTOM CANVAS INC., Etobicoke, ON

DESIGNER: Mike Bennett, Bennett Custom Canvas
FABRICATORS: Mike Bennett and Michaela Bruton, Bennett Custom Canvas
PROJECT MANAGER: Mike Bennett, Bennett Custom Canvas
INSTALLERS: Mike Bennett and Michaela Bruton, Bennett Custom Canvas
MATERIALS USED: Sunbrella fabric, Sunguard Bonded Poly thread, YKK #10 Zips, Stayput Fasteners and 30ga smoke tinted vinyl windows, 7/8” SS tubing, all other materials supplied by George N. Jackson Ltd.

PROJECT DESCRIPTION: Our client came to us with a request to build an enclosure to shelter his family for their trips back and forth to Toronto Island, but being a young urban professional, he wanted something that looked "cool". From the tinted windows, to the organic frame design, to the compelling color combination of red and black, this thing screams "cool". I mounted two new sets of oar lock pads to the innertubes to act as the pivots for the two piece roof. The forward section of the roof is removable to leave a free-standing four piece bimini over the steering consol. A window was installed in the forward section of the roof to promote visibility while standing at the helm. To allow greater accessability at the midship entry points, I arched the legs of the frames forward and aft. In fact, all of the legs of the frames and the bracing are arched for function and aesthetics. The most difficult hurdle with this project was securing the enclosure panels to the inflatable tubes. I accomplished this with a combination of stay-put fasteners that hook to the existing rub-rail as well as some strategically placed mushroom caps glued to the tubes. Finally, I finished off the roof and all panels and with black trim to complement the colors of the boat.

SEAFARER CANVAS, Norwalk, CT

DESIGNER: Bill Ashley, Seafarer Canvas FABRICATOR: Manuel Guaman, Seafarer Canvas
PROJECT MANAGER: Bill Ashley, Seafarer Canvas
INSTALLER: Jeff South, Seafarer Canvas
MATERIALS USED: Strataglass, Textalene screening, Sunbrella

PROJECT DESCRIPTION: The project is a full enclosure on a 25' Chris Craft. The purpose of this project was to give the client a more contemporary look. While updating the look was a goal, the main purpose of the project was to extend the client's boating season. This was accomplished by adding camper back where there had previously been an aft curtain. The only complex part of the project dealt with creating an entirely new framework. The two 7/8” stainless steel frameworks had to be lined up perfectly in order to create a fully seamless enclosure.

SEAFARER CANVAS, Norwalk, CT

DESIGNER: Bill Ashley, Seafarer Canvas
FABRICATOR: Manuel Guaman, Seafarer Canvas
PROJECT MANAGER: Bill Ashley, Seafarer Canvas
INSTALLER: Manuel Guaman, Seafarer Canvas
MATERIALS USED: 7/8” stainless steel, Sunbrella, Strataglass

PROJECT DESCRIPTION: The purpose of this project was to give the client's boat an updated look. We were updating the look by replacing all his frames and adding a camper where there had previously been an aft curtain. The camper back was added to provide the client with an extended boating season and add value to his boat. The complexity in this project was matching of the front and back frame to create a smooth transition in the tops. The large back panel had to curve back in, under the cushions while remaining completely smooth.

MIKES MARINE CUSTOM CANVAS, Virginia Beach, VA

DESIGNERS: Mike Johnson, Mikes Marine Custom Canvas and Jim Carter the boat owner
FABRICATORS: Barb Camacho and Darlene Phillips, Mikes Marine Custom Canvas
PROJECT MANAGER:: Mike Johnson, Mikes Marine Custom Canvas
INSTALLERS: Dan Johnson and Brian Johnson, Mikes Marine Custom Canvas
MATERIALS USED: Sattler Yachtmaster Premium by Sattler NA, Strataglass 40ga clear, Makralon polycarbonate 60ga by Bayer supplied by Performance Textiles, YKK #10 marine zippers supplied by TriVantage

PROJECT DESCRIPTION: Redesigned flybridge bimini and enclosure, plus new aft deck enclosure on a three year old Silverton. The shape of the bimini was a challenge, seven feet wide at the front, eleven feet wide at the back, but all one piece. The windows with u-zippers fore and aft swing up, and the door curtains swing in and snap to walk onto the side decks. The aft deck windows have a distinctive shape that sets this boat apart from the others in the marina.

SHARPS CUSTOM CANVAS INC, Georgetown, SC

DESIGNER: Chris Sharp, Sharps Custom Canvas Inc
FABRICATORS:: Chris Sharp, Jim White and Jonny Sharp, Sharps Custom Canvas Inc
PROJECT MANAGER: Chris Sharp, Sharps Custom Canvas Inc
INSTALLERS: Chris and Jonny Sharp, Sharps Custom Canvas Inc
MATERIALS USED: Sunbrella, 40 mil Seaflex clear vinyl, Ykk Marinemate zippers, 18 0z vinyl, .065 x 1" 316 Stainless Steel tubing and fittings, Lift the Dot fastners
PROJECT DESCRIPTION: A full flybridge enclosure with a two part top. A lower sunshade top with zipout access to upper station. All new two part bimini top with stainless steel frame and full enclosure with U shape zipouts. All new cockpit sunshade with stainless steel frame. Customer wanted full protection from elements with options for ventilation. Also wanted to be able to sit out of elements in lower aft deck. Customer wanted to be able to remove all enclosure and aft part of flybridge top for hot weather use. Lower station top has removable cutout for access to flybridge area.

SEACANVAS, Egg Harbor Township, NJ

DESIGNER: Carl Pellegrini, SeaCanvas
FABRICATOR: Carl Pellegrini, SeaCanvas
PROJECT MANAGER: Carl Pellegrini, SeaCanvas
INSTALLER: Carl Pellegrini, SeaCanvas
MATERIALS USED: Sunbrella, Tenara thread, .40ga Crystal Clear, 316 1" stainless steel, YKK #10 coil tooth zippers

PROJECT DESCRIPTION: A request for a redesign of the existing canvas by recreating new stainless steel frames with proper crown and profile look. 40ga window vinyl was chosen for its ease of care without the need for multiple waxing per year and no issues regarding coatings getting stained. The thread used prevents the need for restitching. Two U-zip windows for ventilation when the full enclosure is in use. Secure aft main frame to arch in two positions for added frame stability. The frame bends were tough in that all three frames were different widths to fit the shape of the boat.

SEACANVAS, Egg Harbor Township, NJ

DESIGNER: Carl Pellegrini, SeaCanvas
FABRICATOR: Carl Pellegrini, SeaCanvas
PROJECT MANAGER: Carl Pellegrini, SeaCanvas
INSTALLER: Carl Pellegrini, SeaCanvas
MATERIALS USED: Sunbrella Supreme, .040 Crystal Clear, Tenara thread, 316 stainless steel tube in 1" and 1 1/4"

PROJECT DESCRIPTION: Design dodger and bimini for a bluewater sailboat. Traditional dodger design, highest quality stainless steel tubing. A three frame 1 1/4" stainless steel bimini frame and two frame 1" stainless steel dodger frame. Purpose is to provide protection from everyday elements including bluewater on deck. Client request include strong frame design and easy care fabric.

BENNETT CUSTOM CANVAS INC, Toronto, ON

DESIGNER: Mike Bennett, Bennett Custom Canvas Inc
FABRICATORS: Mike Bennett and Michaela Bruton, Bennett Custom Canvas Inc
PROJECT MANAGER: Mike Bennett, Bennett Custom Canvas Inc
INSTALLERS: Mike Bennett and Larry Roland, Bennett Custom Canvas Inc
MATERIALS USED: Sunbrella, 30ga clear vinyl, YKK #10 and #5 zippers, Lift the Dot fasteners, stainless steel frames from Stainless Outfitters supplied by George N. Jackson, Lexan from GE Polymershapes

PROJECT DESCRIPTION: One of many Beneteaus we have outfitted this year. This project was designed to maximize cockpit space and visibility while at the same time complementing this yachts' low and rounded lines. The client wanted a full outfitting that complemented the aesthetics of his new Beneteau with optimal space and visibility. He wanted to get away from the traditionally smaller dodgers that make for an awkward transition to the larger bimini. Because of the arge beam, I constructed the bimini frame with 1 1/4" stainless steel tube and fittings for added strength and rigidity.

CUSTOM MARINE CANVAS, Noank, CT

DESIGNERS: Capt. Michael Valentine and Katie Bradford, MFC, IFM, Custom Marine Canvas
FABRICATORS: Brian Bennett, MFC, Nick Olsen and Katie Johnson, Custom Marine Canvas
PROJECT MANAGERS: Capt. Michael Valentine and Nick Olsen, Custom Marine Canvas
INSTALLERS: Nick Olsen, Katie Bradford, MFC, IFM, Custom Marine Canvas
MATERIALS USED: Sunbrella, Keder welt, YKK zippers, webbing supplied by TriVantage

PROJECT DESCRIPTION: An awning, sailcover, and bimini for a busy, globetrotting yacht. The awning and bimini had to be easily and quickly set up by tow crew. The sailcover slides into grooves in the boom and contains integral lazy jacks. The large scale of the project and the exactness of the boat captain's requirements were a bit of a challenge. The awning measured 35’ x 22’ and has to be easily deployed by two crew. The sailcover has integral lazy jacks and a multiude of features. The bimini had to be sleek to complement the lines of the boat.

THE NAUTICAL NEEDLE, Holland, MI

DESIGNER: Chris Ritsema, The Nautical Needle
FABRICATORS Chris Ritsema, Kenny De Groot, Cindy Boersema and Andi Hanson, The Nautical Needle
PROJECT MANAGERS Chris Ritsema and Cindy Boersema, The Nautical Needle
INSTALLERS: Chris Ritsema and Kenny Degroot, The Nautical Needle MATERIALS USED: Stamoid manufactured by Ferrari and supplied by TriVantage, Strataglass supplied by TriVantage, Tenara thread supplied by Tri-Vantage, Rainier bonded Windows, Lenzip zippers, Lift-a-Dot fasteners

PROJECT DESCRIPTION: This project included a skin top that needed to “appear” as a hardtop. The enclosure has seven panels (three with vents installed at the top). It also has five aft drop panels. The customer wanted a tight clean look. The front and sides needed to be free of fasteners so we installed track for that “seamless look”. The front and sides were designed with track to track application. The rear drop required a custom fit around the tower supports. The rear drop was secured with fasteners. The enclosure came together nicely.

COSTA MARINE CANVAS & ENCLOSURES, Egg Harbor City, NJ

DESIGNER: Chris Costa, Costa Marine Canvas
FABRICATORS: Chris Costa and Kevin Jelinski, Costa Marine Canvas
PROJECT MANAGER: Chris Costa, Costa Marine Canvas
INSTALLERS: Chris Costa and Kevin Jelinski, Costa Marine Canvas
MATERIALS USED: Herculite Riviera Marine fabric, YKK UV zippers, Tenara thread, Costa track, clear acrylic glass, Costa Clear Elite

PROJECT DESCRIPTION: Customer wanted a rigid enclosure for flybridge on a 82’ Viking. Front center panel would need to open and air vents installed at top of front panels. Border widths and seam placements were important. The size of the enclosure required special handling and added time. We decided to break into five panels to minimize vertical zipper lines. The front center panel was enlarged to match the size of the windshield. We have four vertical zipper lines plus small border on aft edge of sides. As top border fades into corner we narrowed the border to provide a cleaner look.

CANVAS EXPERTS INC, Ocean City, MD

DESIGNER: Michael Varga, Canvas Experts Inc
FABRICATOR: David Taylor, Canvas Experts Inc
PROJECT MANAGERS: Michael Varga and David Taylor, Canvas Experts Inc
INSTALLERS: Michael Varga and Marty Taylor, Canvas Experts Inc
MATERIALS USED: Riviera by Herculite and distributed by TriVantage, Tenara 2800 denier distributed by Komar Alliance, 8.5mm keder rope distributed by American Keder, YKK #10 zippers, 3/4" double bias binding is stamoid and distributed by TriVantage. the Costa track distributed by TriVantage, EZ2CY

PROJECT DESCRIPTION: A four sided semi rigid enclosure for the bridge of the boat that would maximize visablity from the helm station. Bent corners to eliminate fabric and zipper lines and double track system on the sides. The front corners were heated on a line bender to maximize visability from the bridge and sides are on double track systems to access ventilation.

NAUTILUX CUSTOM CANVAS, Red Bank, NJ

DESIGNER: Darren Arthur, MFC, Nautilux Custom Canvas
FABRICATOR: Darren Arthur, MFC, Nautilux Custom Canvas
PROJECT MANAGER: Darren Arthur, MFC, Nautilux Custom Canvas
INSTALLER: Darren Arthur, MFC, Nautilux Custom Canvas
MATERIALS USED: .40 Ga Strataglass, No See Um Screening, #10 YKK sippers, Sunbrella, Keder welt, Common Sense Fasteners, rubber garage door seal, 1/8" Line Dot fasteners

PROJECT DESCRIPTION: The newly designed forward windshield for this Main Cat 30 gives the owner just what he was looking for, clarity with no distortion. Even in the cold weather him and his family can go for a comfortable cruise. The windows would sag just before and through the forward corners on the original enclosure. By changing the vertical break on the outboard edge and angling it slightly, I was able to eliminate the sag, almost. A 1/2" negative was taken out of each panel for that specific vertical break. Using all windows increased his visibility.

MIKES MARINE CUSTOM CANVAS INC., Virginia Beach, VA

DESIGNER: Mike Johnson, Mikes Marine Custom Canvas
FABRICATORS: Dan Johnson, Brian Johnson and Barb Camacho, Mikes Marine Custom Canvas
PROJECT MANAGER: Mike Johnson, Mikes Marine Custom Canvas
INSTALLERS: Dan Johnson, Brian Johnson and Chris Vogel, Mikes Marine Custom Canvas
MATERIALS USED: Sunbrella, Keder welt, YKK marine zippers, UltraSeal, Quick Release Buckles supplied by TriVantage, Strataglass 40ga, Costa track supplied by Performance Textiles, 18oz Tarp vinyl supplied by Mehler Textiles, heavy duty buckles by Bainbridge International, heavy duty SS snap hooks by Prime Industries

PROJECT DESCRIPTION: This three sided center console enclosure is tough, but user-friendly for impatient fishermen who want comfort while running at full speed, but also need quick access to the bow area when chasing a fish. In addition to the tight fit of the curtains around the windshield, console, and gunwales, the heavy duty adjustable hook straps on the door allow for all of the above. The leading edge of the doors had to attach to the solid windshield with track and continue down the console. This required several release zippers per door, plus three cutouts with flaps each.

CAPE CANVAS & RIGGING, West Yarmouth, MA

DESIGNER: Don Desroches, Cape Canvas & Rigging
FABRICATOR: Don Desroches, Cape Canvas & Rigging
PROJECT MANAGER: Don Desroches, Cape Canvas & Rigging
INSTALLER: Don Desroches, Cape Canvas & Rigging
MATERIALS USED: .040 Strataglass, Stamoid Open, #10 YKK zippers, shockcord & hooks, SS snap shackles, Polypro webbing, SS fender hooks, Solar thread, Pantex pattern plastic, supplies purchased from Bainbridge International, Kellogg and Pennsylvania Thread Company

PROJECT DESCRIPTION: Center console wing enclosure designed to stand up to off shore fishing while remaining removable. By using concave center mount track, eyestraps, snap shackles, and lacing knobs, we maximized strength and ease of use. The windshield and side pannels are one piece, connected with hinges. The top aft corners of the side pannels are securesd with snap shackles to eyestraps. The wings are cut with hollowed edges and act like a sail underway, filling with air but never flapping. The wings roll up for fishing and can be easily removed, and stow, like the windshield section.

MIKES MARINE CUSTOM CANVAS, Virginia Beach, VA

DESIGNER: Mike Johnson, Mikes Marine Custom Canvas
FABRICATORS: Dan Johnson, Barb Camacho and Mike Johnson, Mikes Marine Custom Canvas
PROJECT MANAGER: Mike Johnson, Mikes Marine Custom Canvas
INSTALLERS: Dan Johnson and Mike Johnson Mikes Marine Custom Canvas
MATERIALS USED: 1” stainless tubing, EZ Frame software, Sunbrella, Strataglass 40ga, Keder welt, Flex-a-rail, YKK marine zippers #10, black Grab bars supplied by Performance Textiles

PROJECT DESCRIPTION: A new dodger with extra large removable windows, including a swing up center window that snaps to the reinforced aft pocket. The client had us remove an existing ten foot long bimini with enclosure to build the new dodger, but, for his comfort, wanted to keep the old canvas in place while we were constructing the new. The windows attach to the fiberglass with track and zippers and velcro. The frame is supported by forward stanchions and side grab rails, eliminating the need for aft tensioning straps. The client later added a bimini and connector to fully cover his cockpit.

DRH CANVAS & MARINE LTD., Halifax, NS

DESIGNER: Shawn Hickey, CC, DRH Canvas & Marine Ltd
FABRICATOR: Shawn Hickey, CC, DRH Canvas & Marine Ltd
PROJECT MANAGER: Dave Hickey, MFC, DRH Canvas & Marine Ltd
INSTALLERS Dave Hickey, MFC, and Roland Smeltzer, DRH Canvas & Marine Ltd
MATERIALS USED: Sunbrella by Glen Raven, Strataglass 30ga, Tenara thread by WL Gore, 1" double fold bias binding by Glen Raven, Soltis 86 Ferrari supplied by Trican Corporation, #10 HD YKK zippers, DOT Fasteners, SS thimbles, eyepads supplie by J. Ennis Fabrics

PROJECT DESCRIPTION: A full enclosure with custom screens and smiles for a 2004 Maxium 401 cruiser. Customer wanted the front three windows and front two side windows to have smiles and screens. These screens were installed on top of the smile zippered windows. Both window and screen can be rolled up or down independantly of each other. The two safety handles had to be installed incooperating d-rings on aft roof and eye pads on gunnels. These straps are positioned to stabilize forward access to boat deck.

DRH CANVAS & MARINE LTD., Halifax, NS

DESIGNER: Dave Hickey, MFC, DRH Canvas & Marine Ltd
FABRICATORS: Dave Hickey, MFC, Shawn Hickey, CC, and Roland Smeltzer, DRH Canvas & Marine Ltd
PROJECT MANAGER: Dave Hickey, MFC, DRH Canvas & Marine Ltd
INSTALLERS: Staff, DRH Canvas & Marine Ltd
MATERIALS USED: Ss tubing 065 wall & ss fittings, centre rail track and kedder welt, Sunbrella by Glen Raven, Startaglass 40 mil, Tenera thread by WL Gore, #10 HD zippers by YKK, 1 " binding , miscellaneous fasteners

PROJECT DESCRIPTION: A dodger and frame for Nancy May , a classic O'Day 28. The companion way had to have a custom cover installed, then the dodger could be installed with frame and track installation. The client wanted a good seal at the deck and a strong frame with an aft handle. Designing a cover for the companion way that would look like it was factory installed and a clear view through the windows was very important to the customer. The frame had to clear the boom when the sail was set. Track installation for the dodger gave a very clean look.

CUSTOM COVERS LLC, Salt Lake City, UT

DESIGNER: Justin Jones, Custom Covers LLC
FABRICATORS: Justin Jones, Ilya Tiourine and Kelly Albrecht, Custom Covers LLC
PROJECT MANAGER: Justin Jones, Custom Covers LLC
MATERIALS USED: Weathermax 80 supplied by Miami Corporation, #10 waterproof zipper from LenZip

PROJECT DESCRIPTION: A travel cover for the customer who does not want snaps installed on their boat, yet want the ability to cover their boat while trailering the boat on the highway with out the cover causing damage to the boat. Key details include well placed side tie down hooks on the end instead of wrapping around the trailer so the webbing is held away from the boat. Distinctive fastening system between the tower legs so there are only two places where the belly band detaches to go around the tower legs.

MIKES MARINE CUSTOM CANVAS, Virginia Beach, VA

DESIGNER: Mike Johnson, Mikes Marine Custom Canvas
FABRICATORS: Dan Johnson, Brian Johnson and Barb Camacho, Mikes Marine Custom Canvas
PROJECT MANAGER: Mike Johnson, Mikes Marine Custom Canvas
INSTALLERS: Dan Johnson, Brian Johnson and John Conoway, Mikes Marine Custom Canvas
MATERIALS USED: Weathermax 80, Costa track supplied by Performance Textiles, Duradot snaps supplied by TriVantage, quick release buckles/straps

PROJECT DESCRIPTION: The full t-top cover attaches with track at the top, snaps at the rubrail, underneath, plus quick release buckle/straps at the stern. The cover is two pieces, with zippers at the midway point, plus a door zip in the aft wall for access from the swim platform. The cover is capable of withstanding high winds, and can actually be trailered, yet it is light weight and easy to install. The cover was a challenge to build due to the large size and curved top attachment. Also, the owner wanted as few fasteners showing as possible.

DRH CANVAS & MARINE LTD, Halifax, NS

DESIGNER: Shawn Hickey, CC, DRH Canvas & Marine Ltd
FABRICATOR: Shawn Hickey, CC, DRH Canvas & Marine Ltd
PROJECT MANAGER: Shawn Hickey, CC, DRH Canvas & Marine Ltd
INSTALLER: Shawn Hickey, CC, DRH Canvas & Marine Ltd
MATERIALS USED: Sunbrella by Glen Raven, Tenera thread by WL Gore, Lift-The-Dot fasteners, 18 oz PVC by Nazil, #10 YKK HD zippers

PROJECT DESCRIPTION: A full cover for the interior of a stem boat which fits on the cowling. Beacuse of the smoke stack, and the steam box, this equipment had to be kept clean and dry. The interior was a beautiful wood finish which required protection from rain and the sun. The fit had to be tight, but easy to install. All the fasteners had to be installed so as not to danage the fine finish of the cowling. A zipper was used to help ease the installation. The owner did not want any fabric on the hull or deck, so this was the chosen design path.

CANVAS EXPERTS INC, Ocean City, MD

DESIGNER: David Taylor, Canvas Experts Inc
FABRICATOR: David Taylor, Canvas Experts Inc
PROJECT MANAGER: David Taylor, Canvas Experts Inc
INSTALLERS: David Taylor and Marty Taylor, Canvas Experts Inc
MATERIALS USED: Sauleda S.A. supplied by by Covin Sales Inc, Tenera 2800 denier style supplied by Komar Alliance, webbing was two inch polyester supplied by Eastco Industries, european braid binding and canton fabric supplied by TriVantage

PROJECT DESCRIPTION: A full complete cover to protect the boat during travel and storage. Sixteen templates were patterned to create this job. It took nine and a half hours to pattern and it took over eighty hours to sew. All edges of acrylic fabric where covered with an acrylic braid binding so that a soft edge would touch the boat. Canton fabric was used on anything that needed protection fron the acrylic fabric.

SS CANVAS, Baltimore, MD

DESIGNER: Scott Shaneybrook, SS Canvas
FABRICATOR: Scott Shaneybrook, SS Canvas
PROJECT MANAGER: Scott Shaneybrook, SS Canvas
INSTALLER: Scott Shaneybrook, SS Canvas
MATERIALS USED: Sunbrella and Gortex thread both supplied by Trivantage

PROJECT DESCRIPTION: The cockpit cover on a 42' Fountain Executioner was constructed with solution-dyed acrylic and a bra is incorporation by gypsy snaps to cover the custom paint job on the bow.

SHARPS CUSTOM CANVAS INC, Georgetown, SC

DESIGNER: Chris Sharp, Sharps Custom Canvas Inc
FABRICATORS: Chris Sharp and Jim White, Sharps Custom Canvas Inc
PROJECT MANAGER: Chris Sharp, Sharps Custom Canvas Inc
INSTALLERS: Chris Sharp and Jonny Sharp, Sharps Custom Canvas Inc
MATERIALS USED: Sunbrella, Keder Welt, YKK Marinemate Zippers, SS Quick pins on 5/16 Bunji cord, 1' Velcro, 40 mil clear vinyl reinforcements

PROJECT DESCRIPTION: Cockpit cover with removable side wings with cutouts for lines split open for ease of handling dock lines. Customer wanted a better functioning cover with the ability to easily remove sides. Over head fastners were replaced with PVC track and zipper release welt. Customer also wanted to break up the boring white color scheme of canvas. Charcoal grey was chosen to better hide dirt and bird deposits. Upper station seat covers were made in same color. Customer can now install and remove cover with less hassle and loves the color. Looking to build new enclosure in same color fabric.

MARINER CANVAS, New Bern, NC

DESIGNER: Pamela Vana, Mariner Canvas
FABRICATOR: Pamela Vana, Mariner Canvas
PROJECT MANAGER: Pamela Vana, Mariner Canvas
INSTALLER: Pamela Vana, Mariner Canvas
MATERIALS USED: Sunbrella fabric & binding, Patio500 marine vinyl, Phifertex, Phiferware products, Strataglass 30ga and 40ga, Ebinger leather, 30ga clear UV vinyl, YKK #10 UV zippers, DOT fasteners, Gore Tenara thread, 1” 16-gauge stainless steel tubing, stainless steel fittings and parts

PROJECT DESCRIPTION: Strong stainless-steel framework supports all canvas. Free-standing bimini-top framework includes solar-panel supports fabricated for close tolerances with bimini height, twin backstays, and mainsail boom. This bimini-top includes twin backstay cutouts with no-leak socks, sailview window with inside controls for cover, and full enclosure. The design includes a connector with wide view window, and dodger dimensions which provide visibility from the helm and cockpit. The design was to be sturdy, safe and functional at anchor as well as under sail. The project was to extend livability aboard.

CUSTOM COVERS LLC, Salt Lake City, UT

DESIGNER: Justin Jones, Custom Covers LLC
FABRICATORS: Justin Jones, Rick Burgin and Kelly Albrecht, Custom Covers LLC
PROJECT MANAGERL: Justin Jones, Custom Covers LLC
INSTALLERS: Justin Jones and Rick Burgin, Custom Covers LLC MATERIALS USED: Sunbrella Fabric, 7/8” stainless steel tubing and Hardware supplied by TriVantage, #10 Maritime zippers from LenZip Manufacturing

PROJECT DESCRIPTION: The Folding Canopy Top (FCT) on this 21’ Nautique V-Drive was built and designed to stand out from all of the other tops. Ultimately the purpose of the FCT is to provide shade, however this particular project was for one of the local boat dealers who ordered this boat to use as one of there premiere displays boat for the local boat show. It has a unique design to compliment the interior and general design of the boat. The colors are matched to the interior down to the black binding to match the black welt of the interior.

MIKES MARINE CUSTOM CANVAS, Virginia Beach, VA

DESIGNER: Mike Johnson, Mikes Marine Custom Canvas
FABRICATORS: Dan Johnson, Mike Johnson and Barb Camacho, Mikes Marine Custom Canvas
PROJECT MANAGER:: Mike Johnson, Mikes Marine Custom Canvas
INSTALLERS: Dan Johnson and Mike Johnson Mikes Marine Custom Canvas
MATERIALS USED: 1” stainless steel tubing and fittings supplied by Performance Textiles, stainless steel slide track and carriers, Stamoid top vinyl, Costa track, Keder welt, YKK #10 marine zippers

PROJECT DESCRIPTION: An affordable, retractable, sturdy, cockpit sunshade large enough for adequate protection but easily retracted and out of the way when not needed. The slide track and carriers make it easy for one person to operate. The canvas has release zippers at the front track that allow easy access to rods above. The main frame has a double crown for added height and drainage, plus a crowned mid-bow attached with stainless steel tees. The obstructions on the hardtop in the way of attachment and retracting were a nightmare, but the top looks like a dream.

CUSTOM CANVAS OF CHARLESTON, Charleston, SC

DESIGNERS: Jeri Perillo and Jim Perillo, Custom Canvas of Charleston
FABRICATORS: Linda Flora and Jeri Perillo, Custom Canvas of Charleston
INSTALLERS: Jeri Perillo and Jim Perillo, Custom Canvas of Charleston
MATERIALS USED: 1" stainless tubing, stainless fittings from Prime Industries, Sunbrella, Sea Flex 40ga vinyl, YKK zippers, Tenera thread, Sunbrella 3/4" bias, common sense fasteners

PROJECT DESCRIPTION: A custom designed 1" frame with no straps or legs to obstruct the sides of the cockpit, a new bimini top with a zipper to the dodger, 2 viewing windows, and 6 zippered openings. We had to figure out how to hold the forward bow in place which we did with a strap around the mast since he didn't want legs or straps on the sides. We also had to figure out how to lay out the zippers and flaps so that he could reach the boom, sail and sailcover. Lastly we had to find a way to install two viewing windows without interfering with the zippered openings. We ended up with triangular shaped windows which worked very well.

SEAFARER CANVAS, Norwalk, CT

DESIGNER: Seafarer Canvas, Bill Ashley
FABRICATORS: Seafarer Canvas, Manuel Guaman and Dolly Sanchez
PROJECT MANAGER Seafarer Canvas, Bill Ashley
INSTALLER: Seafarer Canvas, Jeff South
MATERIALS USED: Albany Foam

PROJECT DESCRIPTION: The project is the complete reconstruction and reupholstery of all the exterior cushions on a 39' Searay. The original cushions had been torn apart by racoons and the damage was so extensive that it was impossible to repair or reconstruct the cushions using the originals. We had to get the templates sent from Searay and had to make all the cushions from scratch. We were able to give the customer an almost exact replica of the original Searay cushions.

ENEWHERE, Brooklyn, NY

DESIGNERS: Enewhere Custom Canvas, Dan Ene and Ann Adams
FABRICATOR: Enewhere Custom Canvas, Ann Adams
PROJECT MANAGER: Enewhere Custom Canvas, Dan Ene
INSTALLERS: Enewhere Custom Canvas, Dan Ene and Ann Adams
MATERIALS USED: Seaquest vinyl from Manart Hirsch, Boltasoft vinyl from Bainbridge, Evadri foam from Artel Foams, PVC foamboard from Manart Hirsch, Tasmanian Red Aqualock carpet from Corinthian Textiles

PROJECT DESCRIPTION: A complete redesign and rebuilt of the exterior upholstery for a 38' Fountain. This was an extensive project. It involved rebuilding the helm seats, side panels, aft bench, aft back rest and creating new removable cushions for the aft sun deck that wrapped around newly installed engine cowls. All was rebuilt in rot free PVC foamboard. Evadri reticulated foam was used throughout with drainage provided. Three color matching stripes were designed to create a nice visual flow throughout the boat. Red matching carpet was installed as well.

RAYCO CANVAS, Hartville, OH

DESIGNERS: Rayco Canvas, Carol Turner and Scott Conley
FABRICATOR: Rayco Canvas, Carol Turner and Scott Conley
PROJECT MANAGER: Rayco Canvas, Carol Turner
INSTALLERS: Rayco Canvas, Carol Turner, Scott Conley and Darrell Turner
MATERIALS USED: Softside vinyl from Keyston, foam from Simko, white hydem from Three Rivers, toast Sunbrella from TriVantage

PROJECT DESCRIPTION: To make seats and throw cushions, cover dash and crash pads to replicate the original interior on a 19’ 1948 Chris Craft. Front seat has seat bottom of vinyl and Sunbrella, and loose cushions to replicate the look of the original upholstery. The crash pads had to be a single piece of vinyl heated and stretched to wrap around the dash then hydem was put over the top edge and welt on bottom edge. Dash was padded and covered with vinyl. Making all the cushions fit perfectly and getting the vinyl stretched around the crash padding was complex.

CAPE CANVAS & RIGGING, West Yarmouth, MA

DESIGNER: Cape Canvas & Rigging, Don Desroches
FABRICATOR: Cape Canvas & Rigging, Don Desroches and Stacie Desroches
PROJECT MANAGER: Cape Canvas & Rigging, Don Desroches
INSTALLER: Cape Canvas & Rigging, Don Desroches
MATERIALS USED: Custom vinyl, Sew Foam, 3M Super Adhesive Glue, SS numatic staples from Redrum and Bainbridge, Nautolex from Douglass Industries, Formula Boats

PROJECT DESCRIPTION: The goal of this project was to replace the high use areas, helm bolster chairs, the aft bench divider bolster and two sunpad bolsters while matching the remaining upholstery and staying true to the original design. All wood frames were replaced. Each panel was unstitched, flattened, and patterned. All topstitching and piping matched the original design. Four different types of vinyl, one discontinued, were found after many phone calls and web research. The end result is a seamless transition between new and original.

SEAFARER CANVAS, Norwalk, CT

DESIGNER: Seafarer Canvas, Bill Ashley
FABRICATOR: Seafarer Canvas, Dolly Sanchez
PROJECT MANAGER: Seafarer Canvas, Bill Ashley
INSTALLER: Seafarer Canvas. Jeff South
MATERIALS USED: Sunbrella, Foamat

PROJECT DESCRIPTION: The client wanted to change his old solid colored cushions to a nautically classic stripped pattern while also changing the old soft foam to a high density foam. When changing from a solid to a stripped pattern we had to be carefull to fabricate the cushions keeping in mind that the stripes had to match from cushion to cushion. The client was very satisfied and his Daycruiser was updated to a more classic look that more appropriately fit the boat.

DRH CANVAS & MARINE LTD, Halifax, NS

DESIGNER: DRH Canvas & Marine Ltd, Dave Hickey, MFC
FABRICATORS: DRH Canvas & Marine Ltd, DRH Staff
PROJECT MANAGERS: DRH Canvas & Marine Ltd, Dave Hickey, MFC
INSTALLERS: DRH Canvas & Marine Ltd, DRH Staff
MATERIALS USED: Windsurfer Extra vinyl in red, blue, white and gray,  Vinahide from J. Ennis Fabrics, 2 lb denisty foam 2" to 4" thick from Comfort Foam & Fibre, 1/2" dougfir plywood Mas epoxy resin from OP Fiberglass, SS fasteners, staples and miscellaneous hardware from J. Ennis

PROJECT DESCRIPTION: Complete new cockpit upholstery for 1992 26' Chaparral with all new substraights and foam.  Client wanted a new look and to replace the rotten wood. Client wanted a section of the settee back to be removable for better aft sitting arrangement. To design the settee back with arm to be stable underway at high speeds or to be removed. Manufacturing the substraights to fit properly since old substraights were rotten.

THE NAUTICAL NEEDLE, Holland, MI

DESIGNER: The Nautical Needle, Cindy Boersema
FABRICATOR: The Nautical Needle, Cindy Boersema
PROJECT MANAGER: The Nautical Needle, Cindy Boersema
INSTALLER: The Nautical Needle, Cindy Boersema
MATERIALS USED: Leather from Meade distributing, foam from Grand Rapids Foam Technologies

PROJECT DESCRIPTION: This is an interior of a 34' hand crafted mahogany boat. We had the honor of being chosen to design and manufacture the interior seating areas. The design had to complement the already superior quality of the boat. We did not want something that tried to over power the exterior. Using leather was great and kept with the era of the boat. Patterning and putting together the project with leather having only the hide sizes to work with made the project interesting.

SEAFARER CANVAS, Norwalk, CT

DESIGNER: Seafarer Canvas, Bill Ashley
FABRICATORS: Seafarer Canvas, Louie Fernando, Dolly Sanchez, Manuel Guaman and Jeff South
PROJECT MANAGER: Seafarer Canvas, Bill Ashley
INSTALLER: Seafarer Canvas, Manuel Guaman and Dolly Sanchez
MATERIALS USED: Kravet chanele, Ultraleather, Ralph Lauren, Duralee

PROJECT DESCRIPTION: The project was to do a complete remake of the boat's interior. The customers wanted to update the look of their boat and give it a cohesive feel. The result of the project was a cohesive boat interior that gives each space its own feel.

DRH CANVAS & MARINE LTD, Halifax, NS

DESIGNER: DRH Canvas & Marine Ltd, Dave Hickey, MFC
FABRICATOR: DRH Canvas & Marine Ltd, Staff
PROJECT MANAGER: DRH Canvas & Marine Ltd, Dave Hickey, MFC
INSTALLER: DRH Canvas & Marine Ltd, Staff
MATERIALS USED: Galaxy Wedgewood fabric, Princeport gold fabric and Caravan Berber carpet, lining fabrics and fillers Midhsip cream vinyl supplied by J. Ennis, #6 and #2 brass grommets supplied by Trican Corporation

PROJECT DESCRIPTION: Complete interior renovation of 1991 Bayliner 3870. Replaced all carpeting, drapes and interior upholstery. Customer supplied drapery fabric but left the decision for interior decorating to us. Scale of the job from carpet, drapes and large fixed settee and all the detail included in the finished job - table linens, napkin rings, throw pillows and forward bunk interior hatch cover. Unique designs on throw pillows, napkin rings by the use of grommets.

THE NAUTICAL NEEDLE, Holland, MI

DESIGNER: The Nautical Needle, Cindy Boersema
FABRICATOR: The Nautical Needle, Cindy Boersema
PROJECT MANAGER: The Nautical Needle, Cindy Boersema
INSTALLER: The Nautical Needle, Cindy Boersema
MATERIALS USED: Robert Allen Mileath Fawn, London Town Cocoa Cream Puffs, Wheat Luxury Fabrics, Viva Linen Glen Raven, Edgefield, High Point Collection

PROJECT DESCRIPTION: This Sea Ray was in need of some class. The interior was stark white everywhere. The customer wanted color but still wanted a soft look. The customer wanted no new design, but did want two custom made foot stools with storage. The seating area was a bit of a challenge with the inside curves and the vinyl chosen was very stiff so we had to do some re-patterning in that area. It was more time consuming than thought it would be. Nothing was left undone, including the carpet.

THE NAUTICAL NEEDLE, Holland, MI

DESIGNER: The Nautical Needle, Cindy Boersema
FABRICATOR: The Nautical Needle, Cindy Boersema
PROJECT MANAGER: The Nautical Needle, Cindy Boersema
INSTALLER: The Nautical Needle, Cindy Boersema
MATERIALS USED: Sunbrella High point collection Cabaret Blue Haze, Sunbrella Sahare Sail Cloth, Sunbrella Spa and vellum along with fringes supplied by TriVantage

PROJECT DESCRIPTION This 31' Tiara was having a fabric date crisis. It needed a new comforter, sheets, a curtain, pillows and the side rails recovered. The fabric selection was perfect for this space and gave it a open alluring feeling. The divider curtain had to be patterned and new track installed. It opened up the entire section of this boat and made it alluring. The quilting was done by us and not outsourced.

NORTH BEACH MARINE CANVAS, San Francisco, CA

DESIGNER: North Beach Marine Canvas, Liz Diaz, MFC
FABRICATORS: North Beach Marine Canvas, Liz Diaz, MFC; Maynors Upholstery
PROJECT MANAGER: North Beach Marine Canvas, Liz Diaz, MFC
INSTALLER: North Beach Marine Canvas, Liz Diaz, MFC
MATERIALS USED: Spinnebeck waterproof leather

PROJECT DESCRIPTION: Complete new upholstery for the interior of this Hylas 40 for the live-a-board couple.  They wanted perfection in every detail, way beyond the factory standard. They requested a professional interior as their boat is very important to them and they wanted it done right. All the measurements were altered from 1/4" up to 2” for that perfect fit. They also wanted a stained glass window for their wine cabinet in a nautical motif, something that would represent their good taste.

NEEDLE LOFT INC., Kemah, TX

DESIGNER: Needle Loft Inc, Linda Delgado
FABRICATOR: Needle Loft Inc, Linda Sturdivant
PROJECT MANAGER: Needle Loft Inc, Linda Delgado
INSTALLERS: Needle Loft Inc, Linda Sturdivant and Melissa Sturdivant
MATERIALS USED: maroon Majlite, foam and dacron, velcro

PROJECT DESCRIPTION: New dinnett cushions with a space for the cornor table for customers computer. A need to replace worn cushions and foam while matching the design and fabric pattern.

THE NAUTICAL NEEDLE, Holland, MI

DESIGNER: The Nautical Needle, Cindy Boersema
FABRICATOR: The Nautical Needle, Cindy Boersema
PROJECT MANAGER: The Nautical Needle, Cindy Boersema
INSTALLER: The Nautical Needle, Cindy Boersema
MATERIALS USED: Glen Raven Jazz Spa, Trivantage

PROJECT DESCRIPTION: Purpose was to recover the dining area and update the interior. Curves were a bit of challenge with matching pattern but worth the effort. The fabric is extremely durable and it turned out great.

THE CANVAS LADY, Warwick, RI

DESIGNER: The Canvas Lady, Tonya Ricketts
FABRICATOR: The Canvas Lady, Tonya Ricketts
PROJECT MANAGER: The Canvas Lady, Tonya Ricketts
INSTALLER: The Canvas Lady, Tonya Ricketts
MATERIALS USED: Sunbrella Captains Navy/Oyster, Lexan 40 ga, Strataglass 40 ga, Sea Flex 30 ga, Tenara thread from Tri Vantage, Bainbridge International, Modern Plastics

PROJECT DESCRIPTION: The project was to completely recover the existing canvas for this customer. The customer was heading South and wanted to change the color of the existing canvas, have a better fitting canvas, and also add extra features such as a full awning on the aft deck, dinghy cover while the dinghy was on the davits and an enclosure with optional screening. There was alot of fabric, 55 plus yards, and pieces and parts to get finished in a months time.

CAPE CANVAS & RIGGING, West Yarmouth, MA

DESIGNER: Cape Canvas & Rigging, Don Desroches
FABRICATOR: Cape Canvas & Rigging, Don Desroches
PROJECT MANAGER: Cape Canvas & Rigging, Don Desroches
INSTALLER: Cape Canvas & Rigging, Don Desroches
MATERIALS USED: Sunbrella, .040 Strataglass, heavy duty center mount track, Keder tape, 30nt fiberglass batten, SS jawslides, shockcord & hooks, #10 YKK sippers supplied by Bainbridge International

PROJECT DESCRIPTION: The Batten Framed Bow Dodger provides protection of a traditional bow dodger while eliminating the bulk and bother of a stainless or aluminum frame. The profile of the dodger matches the look of todays moving center consoles. The tight, low slung design, paired with reinforcing ensures the dodger can hold up under extreme conditions. Utilizing zippered connectors and quick release pins the dodger rolls forward for storage or can be stowed in rod storage to get it out of the way. Due to the height and shape visibility from the helm is unaffected. A zip out Strataglass window provides ventilation and access forward to the anchor.

MIKES MARINE CUSTOM CANVAS, Virginia Beach, VA

DESIGNER: Mikes Marine Custom Canvas, Mike Johnson
FABRICATORS: Mikes Marine Custom Canvas, Barb Camacho and Dan Johnson
PROJECT MANAGER: Mikes Marine Custom Canvas, Mike Johnson
INSTALLERS: Mikes Marine Custom Canvas, Brian Johnson and Mike Johnson
MATERIALS USED: Weblon Coastline Plus, Ebbtide tan, 30ga extruded roll vinyl, hear rod clamps, #10YKK Marine Zippers supplied by TriVantage, black heavy duty adjustable buckles from Bainbridge, 3/4" PVC pipe from Lowes

PROJECT DESCRIPTION: The client wanted a new outdoor room to use for sports parties. He asked us for a porch enclosure to hold in the heat and keep out the wind. The curtains are fairly large and had to fit an angled overhead beam on the left, pass around pillars and over a railing, then travel fifteen feet and pass around another set of pillars before returning to the right wall. There were multiple complex measurements and flaps to fill the cutouts around all those obstructions in order to seal out the cold.